Ultrasonic Extraction of 2-Acetyl-1-Pyrroline (2AP) from Pandanus amaryllifolius Roxb. Using Ethanol as Solvent.

2-acetyl-1-pyrroline (2AP) is the compound that gives out the typical aroma and flavour of pandan leaves (Pandanus amaryllifolius Roxb.). This research incorporates ultrasonic extraction to extract the aromatic compound in pandan leaves. The parameters varied in this study are the extraction time, sonicator amplitude, concentration of solvent and the mass of pandan leaves. The experiment was conducted using a central composite design (CCD) model generated by the response surface methodology (RSM). From the extraction process, it can be deduced that the effect of leaves' mass is comparably higher than other parameters, while sonicator amplitude gives the most negligible impact on the process. The obtained p-value was 0.0014, which was less than 0.05. The high R-squared 0.9603 and adjusted R-squared 0.8809 indicate the model is well agreed with the actual data. The optimal control variables of ultrasonic extraction of 2AP are at an extraction time of 20 min, 60% of solvent concentration, amplitude of 25% and 12.5 g of pandan leaves, which produced 60.51% of yield of the extract and 1.43 ppm of 2AP. It is found that the mass of pandan leaves and the concentration of solvent have a significant impact on the extraction process of 2AP.

Overview of Feedstocks for Sustainable Biodiesel Production and Implementation of the Biodiesel Program in Pakistan.

The energy demand of the world is skyrocketing due to the exponential economic growth and population expansion. To meet the energy requirement, the use of fossil fuels is not a good decision, causing environmental pollution such as CO2 emissions. Therefore, the use of renewable energy sources like biofuels can meet the energy crisis especially for countries facing oil shortages such as Pakistan. This review describes the comparative study of biodiesel synthesis for various edible oils, non-edible oils, and wastes such as waste plastic oil, biomass pyrolysis oil, and tyre pyrolysis oil in terms of their oil content and extraction, cetane number, and energy content. The present study also described the importance of biodiesel synthesis via catalytic transesterification and its implementation in Pakistan. Pakistan is importing an extensive quantity of cooking oil that is used in the food processing industries, and as a result, a huge quantity of waste cooking oil (WCO) is generated. The potential waste oils for biodiesel synthesis are chicken fat, dairy scum, WCO, and tallow oil that can be used as potential substrates of biodiesel. The implementation of a biodiesel program as a replacement of conventional diesel will help to minimize the oil imports and uplift the country's economy. Biodiesel production via homogeneous and heterogeneous catalyzed transesterification is more feasible among all transesterification processes due to a lesser energy requirement and low cost. Therefore, biodiesel synthesis and implementation could minimize the imports of diesel by significantly contributing to the overall Gross Domestic Product (GDP). Although, waste oil can meet the energy needs, more available cultivation land should be used for substrate cultivation. In addition, research is still needed to explore innovative solvents and catalysts so that overall biodiesel production cost can be minimized. This would result in successful biodiesel implementation in Pakistan.

Hybrid Membrane Distillation and Wet Scrubber for Simultaneous Recovery of Heat and Water from Flue Gas.

Flue gas contains high amount of low-grade heat and water vapor that are attractive for recovery. This study assesses performance of a hybrid of water scrubber and membrane distillation (MD) to recover both heat and water from a simulated flue gas. The former help to condense the water vapor to form a hot liquid flow which later used as the feed for the MD unit. The system simultaneously recovers water and heat through the MD permeate. Results show that the system performance is dictated by the MD performance since most heat and water can be recovered by the scrubber unit. The scrubber achieved nearly complete water and heat recovery because the flue gas flows were supersaturated with steam condensed in the water scrubber unit. The recovered water and heat in the scrubber contains in the hot liquid used as the feed for the MD unit. The MD performance is affected by both the temperature and the flow rate of the flue gas. The MD fluxes increases at higher flue gas temperatures and higher flow rates because of higher enthalpy of the flue gas inputs. The maximum obtained water and heat fluxes of 12 kg m-2 h-1 and 2505 kJm-2 h-1 respectively, obtained at flue gas temperature of 99 °C and at flow rate of 5.56 L min-1. The MD flux was also found stable over the testing period at this optimum condition. Further study on assessing a more realistic flue gas composition is required to capture complexity of the process, particularly to address the impacts of particulates and acid gases.

Effect of a Different Number of Amine-Functional Groups on the Gas Sorption and Permeation Behavior of a Hybrid Membrane Comprising of Impregnated Linde T and 4,4'- (Hexafluoroisopropylidene) Diphthalic Anhydride-Derived Polyimide.

The bottleneck of conventional polymeric membranes applied in industry has a tradeoff between permeability and selectivity that deters its widespread expansion. This can be circumvented through a hybrid membrane that utilizes the advantages of inorganic and polymer materials to improve the gas separation performance. The approach can be further enhanced through the incorporation of amine-impregnated fillers that has the potential to minimize defects while simultaneously enhancing gas affinity. An innovative combination between impregnated Linde T with different numbers of amine-functional groups (i.e., monoamine, diamine, and triamine) and 4,4'-(hexafluoroisopropylidene) diphthalic anhydride (6FDA)-derived polyimide has been elucidated to explore its potential in CO2/CH4 separation. Detailed physical properties (i.e., free volume and glass transition temperature) and gas transport behavior (i.e., solubility, permeability, and diffusivity) of the fabricated membranes have been examined to unveil the effect of different numbers of amine-functional groups in Linde T fillers. It was found that a hybrid membrane impregnated with Linde T using a diamine functional group demonstrated the highest improvement compared to a pristine polyimide with 3.75- and 1.75-fold enhancements in CO2/CH4 selectivities and CO2 permeability, respectively, which successfully lies on the 2008 Robeson's upper bound. The novel coupling of diamine-impregnated Linde T and 6FDA-derived polyimide is a promising candidate for application in large-scale CO2 removal processes.